Resource Type

Journal Article 6

Year

2021 1

2018 1

2016 1

2010 1

2007 2

Keywords

swirl 2

ECFM-3Z 1

HCCI engine 1

Swirl ratio 1

air/particle flow 1

curcumin 1

diameter 1

diesel engine 1

engine speed 1

entropy-based design 1

hollow 1

industrial pulverized coal boiler 1

initial spray 1

low back-pressure 1

magnussen combustion-model 1

micronization 1

middle 1

paddle wheel anemometer 1

particle dynamic analyzer (PDA) 1

peak pressures 1

open ︾

Search scope:

排序: Display mode:

Micronization of curcumin with biodegradable polymer by supercritical anti-solvent using micro swirl

Kimthet Chhouk, Wahyudiono, Hideki Kanda, Shin-Ichro Kawasaki, Motonobu Goto

Frontiers of Chemical Science and Engineering 2018, Volume 12, Issue 1,   Pages 184-193 doi: 10.1007/s11705-017-1678-3

Abstract: In this work, a swirl mixer was employed to produce the micronized curcumin with polyvinylpyrrolidone

Keywords: micronization     curcumin     polyvinylpyrrolidone     supercritical anti-solvent     swirl mixer    

Influence of mass air flow ratio on gas-particle flow characteristics of a swirl burner in a 29 MW pulverized

Rong YAN, Zhichao CHEN, Shuo GUAN, Zhengqi LI

Frontiers in Energy 2021, Volume 15, Issue 1,   Pages 68-77 doi: 10.1007/s11708-020-0697-9

Abstract: In a gas/particle two-phase test facility, a three-component particle-dynamics anemometer was used to measure the characteristics of gas/particle two-phase flows in a 29 megawatt (MW) pulverized coal industrial boiler equipped with a new type of swirling pulverized coal burner. The distributions of three-dimensional gas/particle velocity, particle volume flux, and particle size distribution were measured under different working conditions. The mean axial velocity and the particle volume flux in the central region of the burner outlet were found to be negative. This indicated that a central recirculation zone was formed in the center of the burner. In the central recirculation zone, the absolute value of the mean axial velocity and the particle volume flux increased when the external secondary air volume increased. The size of the central reflux zone remained stable when the air volume ratio changed. Along the direction of the jet, the peak value formed by the tertiary air gradually moved toward the center of the burner. This tertiary air was mixed with the peak value formed by the air in the adiabatic combustion chamber after the cross-section of / = 0.7. Large particles were concentrated near the wall area, and the particle size in the recirculation zone was small.

Keywords: industrial pulverized coal boiler     swirl burner     air/particle flow     particle dynamic analyzer (PDA)    

Control of peak pressures of an HCCI engine under varying swirl and operating parameters

T. KARTHIKEYA SHARMA,G. AMBA PRASAD RAO,K. MADHU MURTHY

Frontiers in Energy 2016, Volume 10, Issue 3,   Pages 337-346 doi: 10.1007/s11708-016-0401-2

Abstract: In this paper, an attempt is made to analyze computationally the effect of induction swirl in controllingengine, piston bowl geometry, exhaust gas recirculation (EGR) and equivalence ratio under different swirlThe results show that the swirl ratio has a considerable impact on controlling the peak pressures ofA reduction in peak pressures are observed with a swirl ratio of 4 because of reduced in cylinder temperaturesratios suggest that lower intake temperatures, reentrant piston bowl, higher engine speeds and higher swirl

Keywords: HCCI engine     ECFM-3Z     Swirl ratio     peak pressures     engine speed     piston bowl geometry    

Design of an Automatic Test System for Diesel Inlet Swirl and Evaluation Methods

Wang Jichao,Liu Dexin,Feng Hongqing

Strategic Study of CAE 2007, Volume 9, Issue 5,   Pages 85-90

Abstract:

  Swirl is a key parameter that directly influences the efficiency

Keywords: swirl     diesel engine     paddle wheel anemometer     swirl torque meter     steady test bench    

Spray characteristics of high-pressure swirl injector fueled with alcohol

WANG Xibin, CHEN Wansheng, GAO Jian, JIANG Deming, HUANG Zuohua

Frontiers in Energy 2007, Volume 1, Issue 1,   Pages 105-112 doi: 10.1007/s11708-007-0012-z

Abstract: The spray characteristics of methanol and ethanol with high-pressure swirl injector were explored experimentallythat methanol and ethanol had a slightly larger Sauter mean diameter (SMD) than that of gasoline with swirlNumerical simulation could successfully demonstrate the spray characteristics of high-pressure swirl

Keywords: low back-pressure     diameter     initial spray     hollow     middle    

Entropy production analysis of swirling diffusion combustion processes

Deodat MAKHANLALL, Linhua LIU,

Frontiers in Energy 2010, Volume 4, Issue 3,   Pages 326-332 doi: 10.1007/s11708-009-0058-1

Abstract: conducting a parametric investigation to include the effects of wall emissivity, optical thickness, swirlGlobal entropy production rates decrease with the increase in swirl velocity, wall emissivity and optical

Keywords: entropy-based design     radiation transfer     swirl     magnussen combustion-model    

Title Author Date Type Operation

Micronization of curcumin with biodegradable polymer by supercritical anti-solvent using micro swirl

Kimthet Chhouk, Wahyudiono, Hideki Kanda, Shin-Ichro Kawasaki, Motonobu Goto

Journal Article

Influence of mass air flow ratio on gas-particle flow characteristics of a swirl burner in a 29 MW pulverized

Rong YAN, Zhichao CHEN, Shuo GUAN, Zhengqi LI

Journal Article

Control of peak pressures of an HCCI engine under varying swirl and operating parameters

T. KARTHIKEYA SHARMA,G. AMBA PRASAD RAO,K. MADHU MURTHY

Journal Article

Design of an Automatic Test System for Diesel Inlet Swirl and Evaluation Methods

Wang Jichao,Liu Dexin,Feng Hongqing

Journal Article

Spray characteristics of high-pressure swirl injector fueled with alcohol

WANG Xibin, CHEN Wansheng, GAO Jian, JIANG Deming, HUANG Zuohua

Journal Article

Entropy production analysis of swirling diffusion combustion processes

Deodat MAKHANLALL, Linhua LIU,

Journal Article